Not enough bandwidth for new device state.

Home Forums AR Sandbox Forum Not enough bandwidth for new device state.

Viewing 1 post (of 1 total)
  • Author
    Posts
  • #102375
    Anonymous
    Inactive

    Due to the flickering issue I had on my older laptop I went out and bought a newer laptop. But I had to be realistic and get something the family would need/want. So I got a surface pro 4 and dual booted ubuntu onto a separate partition. Some trickery due to UEFI shell, but not horrible.

    That’s done and been struggling with the darn kinect, honestly I was further along with the flickering.

    After some research, turns out that the one USB port is USB 3.0, which is fine except turns out that USB 3.0 isn’t entirely backward compatible on Ubuntu and that I am supposed to disable the xHCI driver. I tried this on ubuntu (not my strongest OS), but even black listing the driver apparently still loads it up as you can see below.

    [ 505.041427] usb 1-1.4: USB disconnect, device number 6
    [ 505.041544] usb 1-1.4.1: USB disconnect, device number 8
    [ 505.042720] usb 1-1.4.2: USB disconnect, device number 7
    [ 505.043102] usb 1-1.4.3: USB disconnect, device number 10
    [ 510.873643] usb 1-1.4: new high-speed USB device number 11 using xhci_hcd
    [ 510.962029] usb 1-1.4: New USB device found, idVendor=0409, idProduct=005a
    [ 510.962043] usb 1-1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
    [ 510.963051] hub 1-1.4:1.0: USB hub found
    [ 510.963112] hub 1-1.4:1.0: 3 ports detected
    [ 511.901523] usb 1-1.4.2: new full-speed USB device number 12 using xhci_hcd
    [ 512.016537] usb 1-1.4.2: New USB device found, idVendor=045e, idProduct=02b0
    [ 512.016551] usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
    [ 512.016558] usb 1-1.4.2: Product: Xbox NUI Motor
    [ 512.016564] usb 1-1.4.2: Manufacturer: Microsoft
    [ 513.445159] usb 1-1.4.1: new high-speed USB device number 13 using xhci_hcd
    [ 513.551162] usb 1-1.4.1: New USB device found, idVendor=045e, idProduct=02ad
    [ 513.551174] usb 1-1.4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
    [ 513.551181] usb 1-1.4.1: Product: Xbox Kinect Audio, © 2011 Microsoft Corporation. All rights reserved.
    [ 513.551186] usb 1-1.4.1: Manufacturer: Microsoft
    [ 513.551191] usb 1-1.4.1: SerialNumber: A44887B20066049A
    [ 515.237089] usb 1-1.4.3: new high-speed USB device number 14 using xhci_hcd
    [ 515.345430] usb 1-1.4.3: New USB device found, idVendor=045e, idProduct=02ae
    [ 515.345444] usb 1-1.4.3: New USB device strings: Mfr=2, Product=1, SerialNumber=3
    [ 515.345451] usb 1-1.4.3: Product: Xbox NUI Camera
    [ 515.345457] usb 1-1.4.3: Manufacturer: Microsoft
    [ 515.345463] usb 1-1.4.3: SerialNumber: A00361900382050A
    [ 515.346343] usb 1-1.4.3: Not enough bandwidth for new device state.

    basically when I run ~$ KinectUtil getCalib 0
    Downloading factory calibration data for Kinect A00361900382050A…

    and it just sits there

    Has anyone gotten past something similar to this – other than buying a differnt laptop. I cannot disable xHCI in latest UEFI Bios, so apparently thats out too.

    I don’t know how to “compile a new kernel” sounds… menacing.

Viewing 1 post (of 1 total)
  • You must be logged in to reply to this topic.

Comments are closed.